Procedure to Setup and Configure iDRAC on Dell PowerEdge Server

How To

Written by:

Have you heard about iDRAC (Integrated Dell Remote Access) which is used to control your server without needing to install any other operating software or hypervisor? This article covers the data about iDRAC. There are a lot of things that iDRAC can do but this article gives you the guide about how can you set up your initial configuration for iDRAC which helps you to log into the web interface. This entails setting up a static IP for iDRAC with the use of either the dedicated port or via the other alternative of sharing the other LAN ports.

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Must Check: Separate First and Last Name In Excel

So, if you want to learn how you can install iDRAC configuration for your system server for now having the pc or for the future, then this step by step guide is going to help you some way or the other effectively. Read the article till the end to know more about it in details.

Configure Static IP for iDRAC

In order to start your configuration, first of all, boot your server and wait till you can see the iDRAC configuration section pops up during the process of booting.

Soon you see this, immediately press the CTRL+E button since the booting process remains for only 5 seconds before the booting process continues.

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Must Check: Sign In Brookdale Associate Account Online

You also hear it saying Press CTRL+E Remote Access Setup within 5 Seconds. Soon you enter the setup, you will find some of the options available there.

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Must Check: Active Directory Tutorial

You might be assured yourself that iDRACx LAN is set to ON status. And since this is an older server, so you can also find it on iDRAC 6. Some of the newer servers now run on iDRAC 9. To set up a static IP for iDRAC, simply take the highlight on the desktop to the bottom via an arrow and hold on LAN PARAMETER and then press on the entering button.

Must Check: Checksur

At the very top, you can find NIC selection, which is recommended to set as DEDICATED. And since Dell PowerEdge server has a dedicated port for iDRAC, it is used as well.

Next, you will have to narrow down quite a bit until you get to IPV4 setting. And if you are using IPv6 in your environment then you can scroll it down a little lower. Make sure you Enable it and then again scroll down to the option IPv4 Address Source and then change the value to Static.

Furthermost, you need to change the IPV4 ADDRESS, DEFAULT GATEWAY, and DNS SERVER SETTING AND SUBNET MASK.

Now once you have settled everything in place then go ahead and exit from the iDRAC configuration utility. If you are asked to save the changes, then click on save for sure.

Now while you have done all these steps by step, you can see the booting process starting and it will continue once the server is up and running. You should be able to access the web interface. But to confirm that, make sure that the cable is attached to the dedicated port on the back of the server at the correct place.

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Must Check: Microsoft Virtual Machine Converter

Now, if you want to connect the other computer to the same server then simply type https://ipaddress and you can find iDRAC Login screen opened in front of you.

Setup and Configure iDRAC on Dell PowerEdge Server

Setup and Configure iDRAC on Dell PowerEdge Server

Must Check: Fix Com Surrogate Has Stopped Working in Windows 7

Of any of the version of iDRAC including 6, 7, 8 or 9, it seems that the initial username and the password that you are going to use for login here is Root and Calvin.

Talking about iDRAC version 7 you get a warning soon after making a Login to the server to make sure that you change the default credentials since it is the same for all Dell server.

Frequently Asked Question

How do I connect to Dell iDRAC?

  1. Turn on the managed system.
  2. Press <F2> during Power-on Self-test (POST).
  3. In the System Setup Main Menu page, click iDRAC Settings. …
  4. Click Network. …
  5. Specify the network settings. …
  6. Set the IPv4 or IPv6 network settings, depending on the local configuration.
  7. Click back, click Finish, and then click yes.

Must Check: Install Sportsdevil on Kodi 17.4 Krypton/Jarvis

How Does Dell iDRAC Work?

The iDRAC is a piece of hardware that sits on the server motherboard that allows Systems Administrators to update and manage Dell systems, even when the server is turned off. The iDRAC also provides both a web interface and command line interface that allows administrators to perform remote management tasks

What is iDRAC in Dell Server?

The Dell Remote Access Controller or DRAC is an out-of-band management platform on certain Dell servers. The platform may be provided on a separate expansion card, or integrated into the main board; when integrated, the platform is referred to as iDRAC.

Must Check: How to Enable Virtualization in Windows 10

How do I Get to iDRAC6 Configuration Utility?

To configure your system to use an iDRAC6, use the iDRAC6 Configuration Utility. Press <Ctrl><E> when prompted during POST. If your operating system begins to load before you press <Ctrl><E>, allow the system to finish booting, and then restart your system and try again.

How do I Disable iDRAC on my Dell Server?

  1. To disable access to Lifecycle Controller at system startup:
  2. Press <F2> during POST. …
  3. Select iDRAC Settings. …
  4. Select the Lifecycle
  5. Under Lifecycle Controller, select Disabled.
  6. On the System Setup Main Menu page, select Finish to save the settings.
  7. Select yes to restart the system.

Must Check: Solve the Flashx TV Pair Error on Kodi

What is the Dell iDRAC Port?

The DRAC (Dell Remote Access Controller) is an interface card by Dell which provides out-of-band management. … The DRAC card has several services bound on its dedicated IP; here is the list of the default ports and their usage: 22 Secure Shell. 23 Telnet.

What is the Default iDRAC Password?

If you have opted for secure default access to iDRAC, the iDRAC secure default password is available on the back of the system Information tag. If you have not opted for secure default access to iDRAC, then the default username and password are “root” and “Calvin”.

How do I Reset my iDRAC?

Open your browser, enter the IP address of your iDRAC interface and access its web interface. Login using the default user (root) and password (Calvin). Click on the Reset button to restart your DRAC iDRAC interface. This tutorial demonstrated how to restart only one iDRAC interface without restarting the dell server.

Must Check: Thevideo.me/Pair or Tvad.me/Pair or Vidup.me

What is iDRAC6 Dell?

The Dell Remote Access Controller 6 (iDRAC6, I stands for integrated) is Dell designed hardware that provides advanced agentless systems management functionality. The iDRAC6 operates independently from the server’s CPU and operating system.

How do I Boot an ISO with iDRAC?

  1. Installation using the KVM Dell iDrac 7
  2. Then click on “Connect”.
  3. Go to the area “Properties” and launch the KVM. Restart the server, and click “F11 Boot Manager”
  4. Go into the menu “BIOS Boot Menu”
  5. Select “Virtual CD” to boot the server from the ISO.
  6. The server will now boot from the ISO image.

Must Check: Determine Mac Address IP from a Mac Address

Final Word

That’s all about it, now you are clear and can play around the iDRAC. You will find more posts on iDRAC further about how can you update your iDRAC server, How to repair it and much more similar.

And now after reading the above article if you have understood about the complete process of installing and using the server.

If you have found this article giving you the clarification related to your query and regarding setup and Configure iDRAC on Dell PowerEdge Server then next thing you can do is let it know to your friends, colleagues, and acquaintances so that they can get help easily and you can also opt for any feedback or remark in the comment section below.

Leave a Reply

Your email address will not be published. Required fields are marked *